This guide covers the LG top-load washer error codes and reminders listed on LG’s US support pages. For each code you get its meaning, the checks an owner can safely try, and when LG’s own pages say to call for service. It covers top-load washers only, not front-load, pedestal, or tower models.
Table of Contents
Quick answer
Most codes on this page start with the same basics. Look for kinked or blocked hoses, objects stuck in the tub or door, and an uneven load or floor, then switch the washer off and restart it. If a code returns after those checks, LG’s pages send you to its service center, 24/7 online chat, or repair request.
Last reviewed: November 21, 2026. Codes can differ by model, so treat your owner’s manual as the final word.
As an Amazon Associate I earn from qualifying purchases.
LG top-load washer error code table
| Code | What it means | What to check | When to contact the manufacturer’s service |
| AE / LE / LE1 | AE means the gears that turn the drum aren’t working properly. LE and LE1 mean the motor is stuck. A coin or object caught between the wash plate and drum can trigger any of the three. | Remove trapped coins or objects from between the wash plate and drum with tweezers. For an LE1 code, empty the tub, look at the bottom, check the seam between the drum and pulsator for a coin, zipper, or paper clip, and take out anything found with pliers. | If nothing is trapped but you hear noise and the drum is affected, request service. If LE1 persists, repair may be needed; contact 24/7 Chat Support. |
| E6 | A clutch error, which can happen when a coin or object is stuck between the pulsator and tub. | Empty the tub, look at the bottom, check the seam between the drum and pulsator for a coin, zipper, or paper clip, and take out anything found with pliers. If it persists, close the water tap and unplug the washer. | Repair service is needed if it persists. Contact 24/7 Chat Support. |
| IE | The washer isn’t filling with water or is not at the right level. Causes include a water outage, a closed tap, a loose or disconnected hose, a kinked or pressed hose, or a frozen hose or tap. | Make sure the hoses are firmly on the taps. Open closed taps counterclockwise. Straighten kinked hoses; if a kink is severe, close the taps, disconnect and reconnect the hoses. For frozen taps, disconnect the hoses, open the taps to test flow, and wrap the taps in a hot cloth for five minutes if no water comes out. Thaw the loose hoses in warm water below 50 °C (122 °F), then reconnect. LG’s documentation gives two slightly different filter-cleaning methods depending on the model: one uses tweezers with the taps closed; another has you disconnect the power cord first and use pliers and a drain hose pushed deeper than 4 in (10 cm) into the drainpipe can siphon during fill. | If it persists, the inlet valve may be faulty; contact an LG service center or request repair. |
| OE | The washer can’t drain, which typically shows after 13 minutes without draining. The cause may be a wrongly installed, kinked, clogged, or frozen drain hose. | Lift the drain hose from the drain hole and run a spin or spin-only cycle. If water drains, clean the blocked drain hole. Straighten a kinked or pressed hose; keep it no higher than 6 cm from the ground and the washer on a firm, level surface. Disconnect the hose and remove clogging objects with tweezers. Pull the washer from the wall and check the hose isn’t bent, clogged, or pinched behind it. Then run SPIN ONLY: press POWER, press SPECIAL USE until SPIN ONLY lights, and press START/PAUSE. With no SPIN ONLY option, start a cycle, wait a few minutes, then pause it. After 8 minutes the unit shows DR and drains. If the spin worked, run a TUB CLEAN cycle. If the hose is frozen, remove the laundry and scoop out any water. Pour warm water (50–60°C) into the tub, close the door, and wait 1–2 hours. If it’s still frozen, wrap a warm wet cloth around the hose. Then run Spin or Spin Only. If nothing drains, wait and retry, then test with Rinse (once) + Spin. Never use boiling water, which is a burn risk. | If it persists, especially if it comes back on an empty wash cycle, contact an LG service center or request repair.” |
| DR | Not an error. The washer timed out and is draining on its own. It happens after 8 minutes of paused and idle or 4 minutes switched on and idle without a cycle. | No check needed. | If it persists, the LED Blinking page says repair may be needed; contact 24/7 Chat Support. |
| UE / uE / Ub | The load is unbalanced. Depending on the model, LG describes this two ways: either uE becomes UE after three failed balancing attempts, or the washer self-balances over up to two cycles, adding about 10 minutes to the spin. | Run RINSE AND SPIN on an empty drum (about 20 minutes). If UE shows again, the washer needs repair. If not, check three things. Leveling: open the lid and see whether the plastic guard is more exposed on one side, then raise the side the tub leans toward. Turn the leg bolts clockwise to raise and counterclockwise to lower, only as far as needed. Test with about six pounds of laundry on RINSE & SPIN and watch for rocking. Use non-skid pads on slippery floors. Load: add items to small loads or lower spin speed; add a few items to single bulky items; untangle sheets and blankets by hand. Wash blankets one at a time on the blanket/duvet cycle, pressed under water and below the plastic ring. Don’t wash electric blankets, mats, curtains, or rubber or bathroom rugs. Fill laundry nets to 2/3 and wash two to three at once, and wash at least two knitted items. Cycle: adding the FABRIC SOFTENER option to Cotton/Normal or Heavy Duty gives a deep rinse. Lowering spin speed or trying Perm Press/Casual also helps. | Contact an LG service center if the washer still can’t balance after you spread the laundry or if UE reappears on an empty-drum test. |
| dE | On most models this means the door is simply open. On models with a drawer-style lock, it means the drawer didn’t close or lock properly. | If the door is open, close it firmly and remove anything blocking it. If it’s a drawer-lock model, switch the washer off, pull the drawer open, check for items under the lid, close firmly, and press Start/Pause. | If it persists with nothing blocking it, contact LG via a service center or 24/7 chat support. |
| dL | A door-lock problem. This can mean an object is blocking the lock, the washer is in a humid room, or on some models the door latch switch itself has failed due to an item in the door, a faulty switch, or a damaged latch. | Remove anything blocking the lock, and try using the washer somewhere less humid. If that doesn’t help, remove any item caught in the door, unplug the washer for 10 seconds, then plug it back in and retry. | If the lock seems damaged or the code continues, contact LG and note that service fees may apply if the damage is traced to the usage environment. |
| tE | A temperature-sensor problem inside the tub, such as a poor contact or faulty sensor. Very hot water poured straight into the tub, or disconnected connectors or a broken circuit, can also cause it. | If you poured hot water into the tub, disconnect the power cord, let the water cool, and then plug it back in. | If it persists, contact LG; a technician inspection or repair may be needed. |
| vS / uS / u5 | A vibration-sensor problem, from a poor contact or faulty sensor. The display may read “u5” or “uS.” | Press Start/Pause. If the code stays, press Power to switch the washer off, then restart it. | If that fails, a technician must inspect it; request service. |
| PE | A water-level sensing problem. This can mean the sensor is struggling to read the water level, sometimes due to humidity, or, on some models, oversudsing from too much detergent.” | Unplug the power cord, wait five minutes, and reconnect. If oversudsing seems to be the cause, run a tub clean cycle with a cleanser such as Affresh. | If PE comes back, contact LG for service. if the cleanser doesn’t help. |
| FE | The tub has too much water. This usually means the water level got too high, possibly from a faulty inlet valve, and the machine may fill even while switched off | Unplug and reconnect the power cord, then run the washer again. If it recurs, turn off the water supply, run a drain-only or spin-only cycle to clear the excess water, and leave the washer unplugged until it’s repaired. | If it recurs, the water-level sensor may be faulty; contact LG for repair. |
| E3 | The drain motor isn’t operating properly. Frozen water inside the washer can also cause it. | Unplug the power cord, reconnect it, and run the washer. If it may be frozen, remove the laundry and scoop out water. Pour warm water (50–60°C) into the tub, close the door, and wait 1–2 hours, or longer if needed. Wrap a warm wet cloth around the drain hose. Run Spin or Spin Only and wait; if nothing drains, then test with Rinse (once) + Spin. | If E3 repeats, the drain motor may need inspection. If it persists after a reset or isn’t due to freezing, request service. |
| FF | Freeze failure. Long cold spells can freeze the inlet or drain hose. OE or FF points to a frozen drain hose, and IE points to frozen inlet hoses or taps. | Thaw the tub and drain hose with warm water, using the OE steps above. For inlet hoses and taps, disconnect the hoses, open the taps, and wrap them in a hot cloth for five minutes if no water flows. Thaw the hoses in warm water below 50°C and reconnect. Test with Rinse (once) + Spin. If you won’t use the washer in winter, remove all remaining water and hold the drain hose downward, unbent. Never use boiling water. | If it persists, contact LG’s 24/7 online chat or request a repair. |
| PF | Not an error. Power was cut, and the washer remembers what it was doing. | Press Start/Pause to start again. | This isn’t a fault, so no contact step is needed unless it keeps recurring. |
| CL | The control lock (child lock) is on. CL blinks on the display. | Find the Control Lock button and hold it for three seconds. CL disappears when the lock is off. The button location differs by model. | This isn’t a fault; no service contact is needed. |
| tCL | Not an error. It reminds you to run a Tub Clean cycle, and may return on some models until you do. | Dismiss it by choosing another cycle or pressing any other button. On models with Tub Clean, power on, select Tub Clean, pour the labelled amount of washing machine cleaner evenly into the tub and press Start/Pause; a chime sounds and the washer turns off after 10 seconds. On models without it, pour in the labelled amount of cleaner, fill the tub about two-thirds, run a cycle for at least two to three minutes, switch off and wait two to four hours. Then power on and run Wash, Rinse, Spin in order. Use an oxygen-bleach cleaner, because chlorine or acidic cleaners can discolor or rust the tub. Run it monthly, and three times in a row if it has been over six months. | If tCL stays after a Tub Clean, request service. |
| EE | A problem with the memory chip (EEPROM) on the main control board. | Try unplugging the washer for 10 minutes. | If that fails, the main control board may need replacing. If that fails, the main control board may need replacing, contact 24/7 Chat Support. |
| PS | The supply voltage is wrong. The washer needs 120Vac (±5%) with correct polarity | The page’s check involves testing the power source, so no owner-safe check is listed here. | If it persists, contact 24/7 Chat Support. |
| D3 | A faulty coupling part. | No owner check is given. | Repair service is required; request it through 24/7 Chat Support |
Quotable facts
- On LG top-load washers, a lowercase uE becomes UE after three balancing attempts, which means the load needs manual redistribution.
- OE appears when the washer has been unable to drain for 13 minutes.
- DR is not a fault: it shows when the washer drains itself after 8 minutes paused or 4 minutes idle.
- PF and tCL are not errors; they signal a power interruption and a Tub Clean reminder.
- Warm water at 50–60 °C is used to thaw frozen drain hoses, and the pages warn against boiling water.
FAQ
What does a UE code mean on an LG top-load washer?
UE means the load is unbalanced. A lowercase uE appears while the washer fills with water and tries to rebalance. After three attempts it becomes UE, meaning you need to redistribute the laundry. LG suggests running RINSE AND SPIN on an empty drum, then checking that the washer is level and the load suits the cycle. If UE returns on the empty drum, the washer needs repair.

Are DR, PF, tCL and CL faults?
No. DR means the washer timed out and is draining itself, after 8 minutes paused or 4 minutes idle. PF means power was interrupted, and the washer remembers its last step; press Start/Pause to continue. tCL reminds you to run a Tub Clean cycle. CL shows that Control Lock is on, and holding the lock button for three seconds turns it off.
What should I check first for an OE drain code?
Start with the drain hose: straighten it and make sure it isn’t clogged or pinched behind the washer. Then run a spin or SPIN ONLY cycle to push out remaining water. If the hose may be frozen, remove the laundry and scoop out water. Pour warm water (50–60 °C) into the tub, wait 1–2 hours, and never use boiling water. If OE comes back on an empty cycle, LG says repair is needed.

When does LG say to contact service?
LG’s pages send you to service when a code persists after the listed checks. For some codes, such as E6, D3 and PS, they point to repair straight away. Examples include no trapped object but a noisy drum (AE/LE/LE1), an IE that returns, or a tE that persists. Use LG’s 24/7 online chat or request a repair on its support site.

Bottom line
Three steps come up again and again in LG’s top-load pages. First, check hoses and the tub or door for kinks, clogs and trapped objects. Second, unplug the washer or switch it off and restart it, using only the waiting times given for each code. Third, when a hose or tap may be frozen, thaw it with warm water and never boiling water. If a code persists after those checks, LG says to contact its service center, use its 24/7 online chat, or request a repair. Next step: find your code in the table and work through the checks listed for it before you call.
Related Article
- LG Washer Buzzing But Not Draining: What’s Actually Wrong
- LG Front-Load Washing Machine Error Code: Meanings & Easy Fixes 2026
- LG TurboWash: What It Is, How to Use It
- Best HE Detergent for LG and Samsung Washers (2026 Guide)
Sources
- LG USA Support, “[LG Top Load Washer] Error Code List,” last updated 03/25/2025.
- LG USA Support, “LG Top Load Washer – LED Blinking Error Codes,” last updated 09/10/2026.
- LG USA Support, “LG Top Load Washer – Troubleshooting An OE Error Code,” last updated 07/24/2026.
- LG USA Support, “LG Washer – What is a Top Load Washing Machine UE/Ub Error Code?“, last updated 09/03/2026
- LG USA Support, “LG Top Load Washer – Troubleshooting an IE Error Code,” last updated 05/29/2026.
- LG USA Support, “LG Washer – Error Code List” (top-load entries), last updated 09/03/2026.


